Best rod seals provider: Basics of fluid pump sealing – A mechanical seal is simply a method of containing fluid within a vessel (typically pumps, mixers, etc.) where a rotating shaft passes through a stationary housing or occasionally, where the housing rotates around the shaft. When sealing a centrifugal pump, the challenge is to allow a rotating shaft to enter the ‘wet’ area of the pump, without allowing large volumes of pressurized fluid to escape. To address this challenge there needs to be a seal between the shaft and the pump housing that can contain the pressure of the process being pumped and withstand the friction caused by the shaft rotating. The gap between the faces on a typical seal is as little as 1 micron – 75 times narrower than a human hair. Because the gap is so tiny, particles that would otherwise damage the seal faces are unable to enter, and the amount of liquid that leaks through this space is so small that it appears as vapor – around ½ a teaspoon a day on a typical application. Find extra info on https://www.dmsseals.com/.
Every other leak path within the mechanical seal is blocked with the use off a gasket, o-ring, wedge (Rubber, PTFE or Flexible Graphite). The other key aspect of a mechanical pump seal is how to maintain the seal. Springs (single or multiple), a metal bellows or just compressed elastomers are used to provide the needed energy to keep pressing the seal faces together. The load the seal faces receive are engineered into the design of the seal. The choice of what is the best depends on the temperature, and nature of what is being sealed (viscosity, abrasiveness, weight (is it a slurry?)). Cartridge Seals are pre-assembled package of mechanical seal components making installation much easier with fewer points for potential mechanical pump seal installation errors to occur. Mechanical seals occasionally require a seal pot to provide a buffer fluid for your double cartridge seals. Seal pots can not only provide a lubricating buffer, but they can also heat or cool the barrier fluid they contain.
Select the appropriate sealing material: There are many types of sealing materials, including many metals, plastics and rubbers. The same material has different performances from different companies. On the other hand, the same seal has different performances in different working conditions or different sealing schemes, so it must be carefully considered when choosing. Note: Be sure to consider seals under the premise of a reasonable sealing scheme, then consider the sealing material, and then consider the seal manufacturer. If you don’t have enough sealing experience, it is best to consider the sealing company first, and let the sealing company consider the sealing scheme and other issues, such as DMS Seals Technology Co.,Limited.
It is ideal for single-acting sealing of reciprocating piston rods or pistons with a wide operating pressure range of up to 20 MPa. The operating temperature range is also wide from -200°C to + 250°C. It has a diameters range from 3 mm to 1600 mm and a working speed of 5 m/s. The seal has a low coefficient of friction and the friction between the contact faces is minimal among all seal types. Moreover, the contact pressure between the mating surfaces is low. It can work without lubrication and is very wear resistant. And it has a long service life.
DMS SEALS’ s bonded seal is ideal for being applied to threaded pipe fittings and plug sealing in Metric, British and BSP systems. The seal has no special requirements for the positioning and processing techniques of the seal groove, so it is an ideal accessory for fast and automatic installation that we highly recommend. The operating temperature range is -30°C ~ 100°C, and the working pressure is less than 39.2 MPa. It is commonly used in a hydraulic oil medium.
Scraper seals are also known as wiper seals. The scraper sealof DMS SEALS can effectively prevent various forms of contamination that cause a hydraulic system failure. It can be mounted on the outside of the piston rod seal of the hydraulic cylinder to protect the hydraulic cylinder from dirt, dust and moisture. It can well protect the hydraulic cylinder from environmental pollution and effectively prevent damage to the hydraulic cylinder parts, causing the system to malfunction. DMS offers a wide range of wiper seals for different hydraulic systems with different characteristics, specifications and combinations.
Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.
The guide belt is a belt-shaped member that guides the moving parts. Its main function is to guide. In order to realize the function of guidance, it must support the guided member, and guide and correct its motion trajectory. In order to realize the guiding function well, it also requires isolation, shock absorption and noise reduction of the guiding parts. Guide belts are mainly used in oil cylinders and cylinders. Due to their excellent performance, they are also widely used in other motion mechanisms. See even more details at https://www.dmsseals.com/.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.